Boral Roofing Nationwide

Boral Roofing: The Pasadena Owner’s Guide

Boral concrete and clay tile roofing in Pasadena typically runs $600-$2,500 for targeted repairs and $8,000-$20,000 for full replacement, with most Boral-compatible underlayment, battens, and replacement tiles available same-day through our supply chain. We stock common Boral profiles including Saxony Slate, Villa Tile, and Cedar Shake in standard color blends, and we pull matching tiles from salvage yards when Boral discontinues a specific lot. Most Pasadena homeowners discover a Boral tile problem after a Santa Ana wind cycle or the first heavy winter rain, when a single cracked hip tile or slipped underlayment reveals itself as a ceiling stain or a rattle they can hear from the bedroom.

Call (562) 203-4508

Which Boral Models This Applies To

Boral’s U.S. roofing division, now operating as Boral Roofing under Westlake Royal Roofing Solutions, produced distinct product lines with incompatible fastening and overlap geometry. The Saxony Slate concrete tile, popular in Pasadena’s 1990s-2000s construction, uses a flat, low-profile interlock with a 14-inch exposure and requires Boral’s own elevating batten clip or an aftermarket equivalent with the same 1.75-inch standoff height. Villa Tile, the S-profile Mediterranean clay, has a deeper water channel and a 10.5-inch exposure; mixing Saxony and Villa replacement tiles on the same roof plane creates a stepped, uneven line that traps debris. Cedar Shake concrete mimics wood shingle dimension but weighs 950 pounds per square, nearly double asphalt, so standard 15-pound felt underlayment fails prematurely beneath it.

To identify your Boral tile, check the underside for an embossed date code and plant mark, or measure exposure and overall length. We cross-reference these against Boral’s archived spec sheets, and when the exact color lot is discontinued, we source from L.A. County salvage or recommend a compatible third-party tile from Eagle or MCA, noting the visual match in writing before any order is placed. Rowan Construction Group Pasadena is an independent service provider, not affiliated with Boral or Westlake Royal.

Signs Your Boral Roofing Is Failing

• Cracked or broken tiles at hips and ridges. These are the highest-stress points on any Boral tile roof; thermal expansion in Pasadena’s 100-plus summer days concentrates at the locked edges, and a single cracked hip tile becomes a funnel for driven rain. We find this most often on north-facing ridges where morning dew lingers.
• Staining on soffits or interior ceilings near valleys. Boral’s concrete and clay tiles are water-shedding, not waterproof; the real seal is the underlayment beneath. When the ASTM D226 Type II felt or self-adhered membrane degrades after 20-25 years, water finds the path of least resistance, usually at a valley intersection.
• Granular debris in gutters that matches your tile color. Concrete tiles shed their color-through surface over time; excessive granules signal advanced wear, often from foot traffic during satellite dish or solar panel installation. Pasadena’s hard water accelerates this if sprinklers hit the roof regularly.
• Visible daylight through the roof deck from the attic. This means a tile has shifted or broken entirely, exposing the underlayment. In Bungalow Heaven and other Pasadena neighborhoods with mature trees, we trace this to branch impact or raccoon traffic more often than owners expect.
• Sagging or rotted fascia behind gutters. Boral tile roofs have heavy runoff; when gutters clog with oak catkins or pine needles, water backs up and saturates the fascia. The tile itself is fine, but the edge detail has failed, and it will take the soffit with it.

Before

After

Replacement Cost & What’s Included

Tile roof repair in Pasadena runs $600-$2,500 depending on access, tile availability, and whether the underlayment beneath the failure point is still intact. A localized repair, swapping six to twelve broken tiles and resealing the underlayment, typically falls at the lower end. When the underlayment has failed across a valley or ridge, requiring removal of adjacent tiles, replacement of the membrane, and reinstallation, costs approach the upper range. Full Boral tile roof replacement, including tear-off, deck inspection, new ASTM D226 Type II underlayment or upgraded self-adhered membrane, and replacement tile, ranges $8,000-$20,000 based on roof complexity and square footage.

Our written quote separates material and labor, names the tile manufacturer and profile, and specifies underlayment grade. Under Clause 1 of the Haven Standard, that price is fixed; no change proceeds without a signed change order. Our 365-Day Done Right Promise covers the repair, and every visit includes a documented photo record of deck condition, underlayment installation, and finished tile placement.

DIY or Call Us?

A homeowner can safely walk the roof perimeter with binoculars to spot cracked tiles, check gutters for debris, and photograph any damage from a ladder for our review. Do not step on Boral tile unless you know the walkable path; concrete and clay tiles crack under concentrated weight, and a broken tile becomes a liability.

What goes wrong fast: tile replacement requires matching the interlock geometry precisely, and underlayment work means removing multiple surrounding tiles without damaging them, then re-battening to the original elevation. The weight of Boral tile, up to 950 pounds per square, makes even partial DIY removal dangerous without proper staging. Pasadena’s hillside lots, common in Linda Vista and San Rafael Heights, add fall risk. For anything beyond visual inspection, call (562) 203-4508. We’ll schedule a free estimate, deliver a written price before any work starts, and stock the correct tile profile from our supply chain.

FAQs