Boral Driveway & Pavers Nationwide

Boral Driveway & Pavers: The Pasadena Owner’s Guide

Boral driveway and paver repair in Pasadena typically runs $5,000-$14,000 for full replacement, while targeted paver reset or base repair starts around $800-$2,500. We stock Boral-compatible edge restraints, polymeric sand, and base material on our trucks, and we can usually assess and quote within 24 hours. Most Pasadena homeowners notice the problem after rain, when pooling water reveals settled base material, or when individual pavers rock underfoot where the bedding layer has washed out.

Call (562) 203-4508

Which Boral Models This Applies To

Boral’s hardscape line in Southern California has shifted over the past decade. If your driveway or patio was installed between 2005 and 2015, you likely have Boral’s Old World or Classic Cobble series, both manufactured at their former Rialto plant with a distinct chamfered edge and nominal 2-3/8 inch thickness. Post-2015 installations typically carry the Stonegate or Venetian lines, slightly thinner at 2-1/4 inches and with a tighter dimensional tolerance. The critical compatibility issue: Old World and Stonegate edge restraints are not interchangeable. The older channel uses a 1-5/8 inch spike spacing; the newer profile compresses to 1-3/8 inch. We learned this the hard way on a reset job near the Rose Bowl in 2019, when a crew assumed universal fit and had to pull 40 linear feet of mismained edging.

To identify your series, lift one corner paver from an inconspicuous spot and check the underside stamp. Boral molded the series name into the bedding face through 2018; after that, look for a four-digit date code plus “SG” or “VN.” If the stamp reads “Boral” with no series code, you have pre-2005 material, and we source compatible base and edge components from Techo-Bloc or Belgard rather than hunting obsolete Boral SKUs. Rowan Construction Group Pasadena is an independent service provider, not affiliated with Boral.

Signs Your Boral Driveway & Pavers Is Failing

• Individual pavers rock or click when stepped on. This usually means the bedding sand has migrated through a compromised joint, leaving a void beneath the paver. In Pasadena’s freeze-free climate, the cause is almost always water intrusion through failed polymeric sand rather than frost heave.
• Visible joint erosion or weed growth between pavers. Polymeric sand degrades under UV exposure and Pasadena’s hard water; once the binder washes out, organic material accumulates and root systems loosen the bedding layer.
• Low spots that hold water 30 minutes after rain stops. This indicates base settlement, often where the Class II aggregate was inadequately compacted or where a utility trench was backfilled with native soil instead of specified aggregate.
• Edge pavers tilting outward or separating from the field. The edge restraint has either rotted (if wood), cracked (if PVC), or pulled its spikes (if aluminum). Boral’s recommended 6-inch spike depth is frequently reduced to 3 inches by installers rushing through hardpan.
• Efflorescence that returns after cleaning. White mineral deposits signal moisture moving through the base and bedding layers; the vapor barrier or drainage slope may be compromised, and the problem will accelerate until the base is corrected.

Before

After

Replacement Cost & What’s Included

The wide range on full replacement reflects paver selection more than labor. Boral’s Stonegate runs roughly $4.50 per square foot at distributor cost; comparable Belgard or Techo-Bloc product ranges from $3.80 to $6.20. Under Clause 1 of the Haven Standard, we itemize material and labor separately in every written quote, so you see exactly where the number comes from. Our 365-Day Done Right Promise covers settling, joint failure, or edge movement at no charge if the base was our work.

DIY or Call Us?

There is no high-tension danger in paver work, but there is a hidden cost in getting the base wrong. A homeowner can safely inspect: lift one paver with a flat pry bar, photograph the bedding layer thickness and condition, and check whether the base aggregate is clean crushed stone or contaminated with native soil. What goes wrong in DIY is almost always compaction. A hand tamper cannot achieve 95% Proctor density; the plate compactor rental is $85 per day, and without a moisture-conditioned base, you will have soft spots within two rainy seasons. We have redone three Pasadena DIY resets in the past two years, each one costing more than the original professional quote because we had to remove the new work to reach the still-failed base. If you have lifted a paver and found mud or organic material where aggregate should be, call (562) 203-4508. We will assess it at no charge and give you a written price before any work starts.

FAQs